dfly 2.4.1 does not like HP DL360G4p and Smart Array 6400 with MSA20

[Tomaž Borštnar <tomaz.borstnar@xxxxxxxx>]

Hello!

	I have a HP DL360G4p machine with 5 gigs of RAM, internal SATA disk and HP SmartArray 6400 controller (2 channels) with 
6400EM card (additional 2 channels attached as daughter card) with MSA20 enclosure with SATA disks - configured as 4 
volumes. Install went fine, but dmesg prints some errors (full dmesg output attached), but here are relevant parts:

bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7

And...

CAM: Configuring 5 busses
CAM: finished configuring all busses (-2 left)
**WARNING** waiting for the following device to finish configuring:
  xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:  func=0xc015423d arg=0
Giving up, interrupt routing is probably hosed

But ciss is seen:
ciss0: <HP Smart Array 6400> port 0x5000-0x50ff mem 0xfdff0000-0xfdff1fff irq 7 at device 4.0 on pci11
ciss1: <HP Smart Array 6400 EM> port 0x5400-0x54ff mem 0xfdf70000-0xfdf71fff irq 5 at device 5.0 on pci11

Anything I can help to test?

Tomaž

Copyright (c) 2003-2009 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
DragonFly v2.4.1.12.g4ff2a-RELEASE #0: Thu Oct 15 19:11:54 UTC 2009
    root@chlamydia.fs.ei.tum.de:/usr/obj/usr/src/sys/GENERIC
TSC clock: 2800121583 Hz, i8254 clock: 1193192 Hz
CPU: Intel(R) Xeon(TM) CPU 3.00GHz (2800.12-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf43  Stepping = 3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x641d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,CX16,xTPR>
  Hyperthreading: 2 logical CPUs
real memory  = 3758043136 (3669964K bytes)
avail memory = 3638521856 (3553244K bytes)
kbd1 at kbdmux0
Pentium Pro MTRR support enabled
fildesc_drvinit() building stdin, stdout, stderr: 
md0: Malloc disk
ACPI: RSDP 0xf4ee0 00024 (v2 HP    )
ACPI: XSDT 0xdfff32c0 00044 (v1 HP     P54      00000002   \M-R\^D 0000162E)
ACPI: FACP 0xdfff3340 000F4 (v3 HP     P54      00000002   \M-R\^D 0000162E)
ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 20090521 tbfadt-707
ACPI: DSDT 0xdfff3440 01A9D (v1 HP         DSDT 00000001 INTL 20030228)
ACPI: FACS 0xdfff3100 00040
ACPI: SPCR 0xdfff3140 00050 (v1 HP     SPCRRBSU 00000001   \M-R\^D 0000162E)
ACPI: MCFG 0xdfff31c0 0003C (v1 HP     ProLiant 00000001      00000000)
ACPI: APIC 0xdfff3200 000B6 (v1 HP     00000083 00000002      00000000)
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
acpi0: <HP P54> on motherboard
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu_cst0: <ACPI CPU C-State> on cpu0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
isab0: <ACPI Generic ISA bridge> port 0x280-0x29f,0x220-0x25f,0x4e-0x4f,0x2e-0x2f on acpi0
isa0: <ISA bus> on isab0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 2.0 on pci0
pci13: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 4.0 on pci0
pci6: <PCI bus> on pcib2
pcib3: <PCI-PCI bridge> at device 0.0 on pci6
pci7: <PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection 82541GI_LF 6.9.6> port 0x4000-0x403f mem 0xfdec0000-0xfdedffff,0xfdee0000-0xfdefffff irq 7 at device 1.0 on pci7
em0: MAC address: 00:0e:0c:a2:fe:5c
pcib4: <PCI-PCI bridge> at device 0.2 on pci6
pci10: <PCI bus> on pcib4
pcib5: <PCI-PCI bridge> at device 1.0 on pci10
pci11: <PCI bus> on pcib5
ciss0: <HP Smart Array 6400> port 0x5000-0x50ff mem 0xfdff0000-0xfdff1fff irq 7 at device 4.0 on pci11
ciss1: <HP Smart Array 6400 EM> port 0x5400-0x54ff mem 0xfdf70000-0xfdf71fff irq 5 at device 5.0 on pci11
pcib6: <PCI-PCI bridge> at device 6.0 on pci0
pci3: <PCI bus> on pcib6
pcib7: <PCI-PCI bridge> at device 28.0 on pci0
pci2: <PCI bus> on pcib7
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7
uhci0: <UHCI (generic) USB controller> port 0x3000-0x301f irq 7 at device 29.0 on pci0
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x3020-0x303f irq 7 at device 29.1 on pci0
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
pci0: <base peripheral> (vendor 0x8086, dev 0x25ab) at device 29.4
pci0: <base peripheral, interrupt controller> (vendor 0x8086, dev 0x25ac) at device 29.5
pci0: <serial bus, USB> (vendor 0x8086, dev 0x25ad) at device 29.7 irq 7
pcib8: <PCI-PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib8
vgapci0: <VGA-compatible display> port 0x2000-0x20ff mem 0xfbff0000-0xfbff0fff,0xfc000000-0xfcffffff at device 3.0 on pci1
pci1: <base peripheral> (vendor 0x0e11, dev 0xb203) at device 4.0 irq 7
pci1: <base peripheral> (vendor 0x0e11, dev 0xb204) at device 4.2 irq 7
isab1: <PCI-ISA bridge> at device 31.0 on pci0
isa1: <ISA bus> on isab1
atapci0: <Intel 6300ESB UDMA100 controller> port 0x500-0x50f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 5 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
acd0: CDROM <HL-DT-ST GCR-8240N/2.01> at ata0-master PIO4
ata1: <ATA channel 1> on atapci0
atapci1: <Intel 6300ESB SATA150 controller> port 0x3060-0x306f,0x3058-0x305b,0x3050-0x3057,0x3048-0x304b,0x3040-0x3047 irq 5 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ad6: 76319MB <Seagate ST3808110AS 3.AJJ> at ata3-master SATA150
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xccfff,0xee000-0xeffff on isa1
pmtimer0 on isa1
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa1
sc0: <System console> at flags 0x100 on isa1
sc0: VGA <16 virtual consoles, flags=0x300>
ppc0: parallel port not found.
ip: MPSAFE
arp: MPSAFE
CAM: Configuring 5 busses
CAM: finished configuring all busses (-2 left)
**WARNING** waiting for the following device to finish configuring:
  xpt:	func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:	func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:	func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:	func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
  xpt:	func=0xc015423d arg=0
Giving up, interrupt routing is probably hosed
Mounting root from hammer:serno/5LRBY913.s1d
tryroot serno/5LRBY913.s1d
Mounting devfs