Re: Hints on kernel config for a dula pII/450 system anyone?

[Gergo Szakal <bastyaelvtars@xxxxxxxxx>]

Matthew Dillon wrote:
>     I'm not sure why the mbuf is shared at that point,
>     but the assertion is definitely in the wrong part of the code path.
>
>     I am going to move the assertion.   Could you try that patch and
>     tell me if it works for compiled-in bridging?

No, it does not seem to help. I am telling more:
I have 2 cards, sk0 (public IP) and sk1 (IP-less) - bridged. I use pf, 
all the filtering is done on sk1.
When only sk0 is plugged in, the crash comes after a few minutes. When 
only sk1 is plugged in, the crash comes right after logging in.
Attaching the dmesg from the last crash.
Copyright (c) 2003, 2004, 2005, 2006 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
DragonFly 1.6.1-RELEASE #5: Sun Sep 17 00:26:38 CEST 2006
    szg@xxxxxxxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/SMP
TSC clock: 446442108 Hz, i8254 clock: 1193240 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (446.42-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
  Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 536870912 (524288K bytes)
avail memory = 509067264 (497136K bytes)
Programming 32 pins in IOAPIC #0
DragonFly/MP: Multiprocessor motherboard
 cpu0 (BSP): apic id:  1, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  0, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x001f0011, at 0xfec00000
Preloaded elf kernel "/kernel" at 0xc073b000.
Pentium Pro MTRR support enabled
md0: Malloc disk
pcibios: BIOS version 2.10
Using $PIR table, 15 entries at 0xc00fded0
npx0: <math processor> on motherboard
npx0: INT 16 interface
compare 0
legacypci0 on motherboard
pcib0: <Intel 82443GX host to PCI bridge> on legacypci0
pci0: <PCI bus> on pcib0
agp0: <Intel 82443GX host to PCI bridge> mem 0xfa800000-0xfaffffff at device 0.0 on pci0
pcib1: <Intel 82443GX (440 GX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci0: <unknown card> (vendor=0x110a, dev=0x0015) at 2.0
pcib2: <DEC 21152 PCI-PCI bridge> at device 3.0 on pci0
pci2: <PCI bus> on pcib2
pci2: <Cirrus Logic GD5446 SVGA controller> at 0.0
sym0: <895> port 0x2000-0x20ff mem 0xfa209000-0xfa209fff,0xfa20a000-0xfa20a0ff irq 17 at device 1.0 on pci2
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
skc0: <Marvell Gigabit Ethernet> port 0x2400-0x24ff mem 0xfa200000-0xfa203fff irq 18 at device 8.0 on pci2
skc0: bad VPD resource id: expected 82 got 55
skc0: (null)
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
miibus0: <MII bus> on sk0
e1000phy0: <Marvell Semiconductor 88E1000* gigabit PHY> on miibus0
e1000phy0:  1000baseTX-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto
sk0: MAC address: 00:30:4f:37:9a:91
skc1: <Marvell Gigabit Ethernet> port 0x2800-0x28ff mem 0xfa204000-0xfa207fff irq 19 at device 10.0 on pci2
skc1: bad VPD resource id: expected 82 got 55
skc1: (null)
sk1: <Marvell Semiconductor, Inc. Yukon> on skc1
miibus1: <MII bus> on sk1
e1000phy1: <Marvell Semiconductor 88E1000* gigabit PHY> on miibus1
e1000phy1:  1000baseTX-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto
sk1: MAC address: 00:30:4f:36:17:dc
pci0: <unknown card> (vendor=0x110a, dev=0x001d) at 4.0 irq 2
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1800-0x180f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1400-0x141f irq 16 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <Intel 82371AB Power management controller> at 7.3
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 8223MB <ST38410A> [16708/16/63] at ata0-master PIO4
Waiting 5 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/ad0s1a
WARNING:  was not properly dismounted
bridge0: MAC address: 5e:ad:1c:75:ea:cc
pflog0: promiscuous mode enabled