Report of a number of problems

["elekktretterr@xxxxxxxxxxxxxx" <elekktretterr@xxxxxxxxxxxxxx>]

Sorry for the multiple posts, I decided it will be better if I post the
entire dmesg since it probably contains more information than I can
describe in my words. Help appreciated. Need to get the net working.



Copyright (c) 2003, 2004, 2005 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
DragonFly 1.3.7-DEVELOPMENT #0: Tue Nov  1 02:46:22 CET 2005
    root@xxxxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC
TSC clock: 1799967216 Hz, i8254 clock: 1193117 Hz
CPU: AMD Athlon(tm) 64 Processor 3000+ (1800.08-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x10ff0  Stepping = 0

Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  AMD Features=0xe0500000<<b20>,AMIE,<b29>,DSP,3DNow!>
real memory  = 1072562176 (1047424K bytes)
avail memory = 1030713344 (1006556K bytes)
Preloaded elf kernel "/kernel" at 0xc0702000.
Preloaded elf module "/modules/acpi.ko" at 0xc0702288.
sched_ithd: stray interrupt 7
Pentium Pro MTRR support enabled
md0: Malloc disk
pcibios: BIOS version 3.00
Using $PIR table, 18 entries at 0xc00fde40
sched_ithd: stray interrupt 7
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
acpi0: <K8T890 AWRDACPI> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_button0: <Power Button> on acpi0
compare 0
compare 0
compare 0
compare 0
compare 0
compare 0
compare 0
compare 0
compare 0
legacypci0 on motherboard
pcib0: <Host to PCI bridge> on legacypci0
pci0: <PCI bus> on pcib0
agp0: <VIA Generic host to PCI bridge> mem 0xc0000000-0xc7ffffff at
device 0.0 on pci0
pci0: <unknown card> (vendor=0x1106, dev=0x5238) at 0.5
pcib1: <PCI to PCI bridge (vendor=1106 device=b188)> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI to PCI bridge (vendor=1106 device=a238)> irq 5 at device 2.0
on pci0
pci2: <PCI bus> on pcib2
pci2: <NVidia model 0140 graphics accelerator> at 0.0 irq 5
pcib3: <PCI to PCI bridge (vendor=1106 device=c238)> irq 5 at device 3.0
on pci0
pci3: <PCI bus> on pcib3
pcib4: <PCI to PCI bridge (vendor=1106 device=d238)> at device 3.1 on
pci0
pci4: <PCI bus> on pcib4
pcib5: <PCI to PCI bridge (vendor=1106 device=e238)> irq 5 at device 3.2
on pci0
pci5: <PCI bus> on pcib5
pci5: <unknown card> (vendor=0x11ab, dev=0x4362) at 0.0 irq 5
pcib6: <PCI to PCI bridge (vendor=1106 device=f238)> irq 5 at device 3.3
on pci0
pci6: <PCI bus> on pcib6
pci0: <unknown card> (vendor=0x11ab, dev=0x1fa7) at 7.0 irq 3
fwohci0: <Texas Instruments TSB43AB22/A> mem
0xdb020000-0xdb023fff,0xdb027000-0xdb0277ff at device 8.0 on pci0
fwohci0: Invalid irq 255
fwohci0: Please switch PNP-OS to 'No' in BIOS
pci_cfgintr: 0:8 INTA routed to irq 3
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:11:d8:00:00:14:c1:a2
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
fwe0: MAC address: 02:11:d8:14:c1:a2
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci0: <unknown card> (vendor=0x1102, dev=0x0002) at 11.0 irq 11
pci0: <unknown card> (vendor=0x1102, dev=0x7002) at 11.1
pci0: <unknown card> (vendor=0x109e, dev=0x036e) at 12.0
pci0: <unknown card> (vendor=0x109e, dev=0x0878) at 12.1
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xb800-0xb8ff mem
0xdb026000-0xdb026fff irq 11 at device 13.0 on pci0
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: MAC address: 00:a0:cc:a2:99:39
atapci0: <VIA 8237 SATA 150 controller> port
0xd000-0xd0ff,0xcc00-0xcc0f,0xc800-0xc803,0xc400-0xc407,0xc000-0xc003,0xbc00-0xbc07 irq 11 at device 15.0 on pci0
ata2: at 0xbc00 on atapci0
ata3: at 0xc400 on atapci0
atapci1: <VIA 8237 ATA133 controller> port 0xd400-0xd40f at device 15.1
on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
uhci0: <VIA 83C572 USB controller> port 0xd800-0xd81f at device 16.0 on
pci0
pci_cfgintr: 0:16 INTA routed to irq 3
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
ukbd0: Logitech USB Receiver, rev 1.10/30.07, addr 2, iclass 3/1
kbd1 at ukbd0
ums0: Logitech USB Receiver, rev 1.10/30.07, addr 2, iclass 3/1
ums0: 16 buttons and Z dir.
uhci1: <VIA 83C572 USB controller> port 0xdc00-0xdc1f at device 16.1 on
pci0
pci_cfgintr: 0:16 INTA routed to irq 3
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
ulpt0: Hewlett-Packard DeskJet 930C, rev 1.00/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
ugen0: Canon CanoScan, rev 1.10/1.00, addr 3
uhci2: <VIA 83C572 USB controller> port 0xe000-0xe01f at device 16.2 on
pci0
pci_cfgintr: 0:16 INTB routed to irq 11
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub2: port error, restarting port 1
uhub2: port error, giving up port 1
uhci3: <VIA 83C572 USB controller> port 0xe400-0xe41f at device 16.3 on
pci0
pci_cfgintr: 0:16 INTB routed to irq 11
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub3: port error, restarting port 1
uhub3: port error, giving up port 1
intr 11 at 50000 > 50001 hz, livelocked limit engaged!
pci0: <USB controller> at 16.4
isab0: <PCI to ISA bridge (vendor=1106 device=3227)> at device 17.0 on
pci0
isa0: <ISA bus> on isab0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
device_probe_and_attach: atkbd0 attach returned 6
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: can't drain, serial port might not exist, disabling
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 38166MB <WDC WD400JB-00ENA0> [77545/16/63] at ata0-master UDMA100
ad4: DMA limited to UDMA33, non-ATA66 cable or device
ad4: 76319MB <WDC WD800JD-22JNA0> [155061/16/63] at ata2-master UDMA33
ad6: DMA limited to UDMA33, non-ATA66 cable or device
ad6: 76293MB <WDC WD800JD-75JNA0> [155009/16/63] at ata3-master UDMA33
acd0: DVD-R <PIONEER DVD-RW DVR-109> at ata1-master PIO4
intr 11 at 7378 < 20000 hz, livelock removed
Mounting root from ufs:/dev/ad0s1a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW  DVR-109 1.57> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
uhub2: port error, restarting port 1
uhub2: port error, giving up port 1
umass0: USBest Technology USB Mass Storage Device, rev 2.00/1.00, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <USB 2.0 Flash Disk 0.00> Removable Direct Access SCSI-2 device 
da0: 1.000MB/s transfers
da0: 250MB (512000 512 byte sectors: 64H 32S/T 250C)
WARNING: da0 si_iosize_max=0, using DFLTPHYS.
WARNING: da0 si_iosize_max=0, using DFLTPHYS.

I should also mention that it occurred to me yesterday that the system
actually restarted itself while the kernel was booting.