Fwd: Re: Kernel Panic: bad isr 0

[TC Lewis <tfox@xxxxxxxxxxxxxxxxxxxxxxxx>]

> > -On [20031122 21:42], TC Lewis (tfox@xxxxxxxxxxxxxxxxxxxxxxxx) wrote:
> > >panic: bad isr 0
> > >Debugger("panic")
> > >Stopped at      Debugger+0x34: movb     $0,in_Debugger.339
> > >
> > >Debugger trace reports: (as best as I can see by my craning my neck around
> > >and reading from the monitor behind me)
> >
> > This is during boot or after boot?
>
> During Boot.
>
>
> > Which devices does it probe?  And can you post a successful
> > /var/run/dmesg.boot?
>
> If you call this successful, at least it's not the same error.
>
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 2CSNAP-20031102-0115 #0: Sun Nov  2 01:38:51 GMT 2003
>     root@xxxxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254"  frequency 1193182 Hz
> CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x660  Stepping = 0
>
> Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
> real memory  = 134205440 (131060K bytes)
> avail memory = 122179584 (119316K bytes)
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 6 entries at 0xc00f0d10
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 
> 0xe4000000-0xe7ffffff at device 0.0 on pci0
> pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 
> on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> installed MI handler for int 14
> ata1: at 0x170 irq 15 on atapci0
> installed MI handler for int 15
> uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 5 
> at device 4.2 on pci0
> installed MI handler for int 5
> usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> chip0: <Intel 82371AB Power management controller> port 0xe800-0xe80f at 
> device 4.3 on pci0
> pci0: <unknown card> (vendor=0x1274, dev=0x1371) at 9.0 irq 5
> pci0: <unknown card> (vendor=0x11c1, dev=0x0440) at 10.0 irq 12
> dc0: <82c169 PNIC 10/100BaseTX> port 0xb000-0xb0ff mem 
> 0xe2800000-0xe28000ff irq 10 at device 11.0 on pci0
> installed MI handler for int 10
> dc0: Ethernet address: 00:a0:cc:5e:26:a9
> miibus0: <MII bus> on dc0
> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> sis0: <NatSemi DP83815 10/100BaseTX> port 0xa800-0xa8ff mem 
> 0xe2000000-0xe2000fff irq 11 at device 12.0 on pci0
> installed MI handler for int 11
> sis0: Ethernet address: 00:40:f4:5f:54:13
> miibus1: <MII bus> on sis0
> ukphy1: <Generic IEEE 802.3u media interface> on miibus1
> ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> installed MI handler for int 6
> fdc0: FIFO enabled, 8 bytes threshold
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> installed MI handler for int 1
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> installed MI handler for int 4
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> installed MI handler for int 3
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> installed MI handler for int 7
> installed MI handler for int 0
> installed MI handler for int 8
> ad0: 6149MB <WDC AC26400B> [13328/15/63] at ata0-master UDMA33
> acd0: CDROM <ATAPI CDROM> at ata1-master PIO4
>
> Manual root filesystem specification:
>   <fstype>:<device>  Mount <device> using filesystem <fstype>
>                        eg. ufs:/dev/da0s1a
>   ?                  List valid disk boot devices
>   <empty line>       Abort manual input
>
> mountroot> ufs:/dev/ad0s1a
> Mounting root from ufs:/dev/ad0s1a
>
>
> > There's always the verbose boot option that can also help.  Also, try
> > booting safely.  These are available if you copy
> > src/sys/boot/i386/loader/loader.rc to /boot
> >
> > --
> > Jeroen Ruigrok van der Werven <asmodai(at)wxs.nl> / asmodai / kita no mono
> > PGP fingerprint: 2D92 980E 45FE 2C28 9DB7  9D88 97E6 839B 2EAC 625B
> > http://www.tendra.org/  | http://www.in-nomine.org/~asmodai/diary/
> > It is better to be silent and be thought a fool, than speak and remove all
> > doubt...
>
>
> -TFox-


-TFox-